Shop

Express Order

Model # Qty

Info

Contact

Account

Quick Change Tool Holders- Mini Lathes

Mini Lathe Quick Change Tool Post Set

Quick Change Tool Post Set for Mini Lathes up to 8" swing.
Wedge locking system.
All working parts hardened and ground.
Approximately 60% of the size of AXA / 100 Series tool post sets.
For center heights of 5/8" to 1"
Machineable bottom holding plate allows mating to variable compound slots.

Change tools in seconds.
Place the toolholder on the toolpost's dovetail, adjust the tool's height with the knurled wheel, lock the nut, and lock the wedge.
No shims necessary.

These sets include the tool post and five tool holders: one each of holder style #1, #2, #4, #7, and #10.

To order the correct tool post for your machine, measure the CENTER HEIGHT of your lathe: this is the distance from the height of the top of the lathe's compound rest to the height of the spindle/chuck centerline.
Match your lathe's center height to a toolpost with a compatible center height range.

In situations where your lathe will accommodate more than one size tool post, secondary variables (such as swing, tool size capacity, rigidity, etc.) should then be considered to select the post that you want for your machine.
Check the individual listings of the different style toolholders below to see the capacities of each series.
Quantity Price Model Description

$219.00 QC-060-ST
060 Quick Change Tool Post Set (0XA)

Style 1 Turning Holder for 060 Mini Tool Post

Holds 1/2" or smaller tool bits.
Quantity Price Model Description
Out of stock
$18.60 QC-060-1
#1 Turning and Facing Holder- 060 Series

Style 2 Turning and Boring Holder for 060 Mini Tool Post

Holds 1/2" or smaller tool bits and boring bars.
Quantity Price Model Description
Out of stock
$19.10 QC-060-2
# 2 Turn, Face, Bore Holder-060 Series

Style 4 Boring Holder for 060 Mini Tool Post

Holds 1/2" diameter boring bars.
Quantity Price Model Description
Out of stock
$38.50 QC-060-4
# 4 Boring Bar Holder-060 Series

Style 7 Cutoff Holder for 060 Mini Tool Post

Holds 1/2" high T-type cut-off blades, such as CUT-P1N and CUT-P1.
Quantity Price Model Description
Out of stock
$29.50 QC-060-7
# 7 Cut Off Holder-060 Series

Style 10 Knurling Holder for 060 Mini Tool Post

Knurls included.
Quantity Price Model Description
Out of stock
$35.50 QC-060-10
# 10 Knurling Holder-060 Series

Phase II Hobby Quick Change Tool System

LIMITED QUANTITY!

Phase II Hobby Quick Change Tool System.
Piston locking system.
This tool post is made to work on lathes with center heights from 5/8"- 1 1/8", and 5- 8 inches of swing.

Designed to fit the popular 7" machines: 7 x 10", 7 x 12", and 7 x 14" mini lathes.

The toolpost is fitted with a machinable T-slot nut to fit machines with a T-slotted compound rest.
The toolpost may also be installed directly to a drilled-and-tapped (8 or 10mm) compound rest with either of the included bolts:
an 8mm bolt (with included through-body bushing) or 10mm bolt.
The tool post body is 1 1/2" high with a base 1 3/4" wide.

The complete set includes one tool post, two turning tool holders, a boring bar holder, and one cutoff tool holder.

To order the correct tool post for your machine, measure the CENTER HEIGHT of your lathe:
this is the distance from the top of the compound to the center of the chuck.
Match your lathe's center height to a toolpost with a compatible center height range.

In situations where your lathe will accommodate more than one size tool post, secondary variables (such as swing, tool size capacity, rigidity, etc.) should then be considered to select the post that you want for your machine.
Quantity Price Model Description Center Height Holds Tool Size
Out of stock
$25.00 PH2-250-069
# 4 Hobby Boring Bar Holder 5/8"- 1 1/8" 3/8" round bar

Phase II Micro Quick Change Tool System

LIMITED QUANTITY!

Phase II Micro Quick Change Tool System.
Piston locking system.
This tool post is made to work on lathes with center heights from 9/32"- 23/32", and 5- 8 inches of swing.

The toolpost is fitted with a machinable T-slot nut to fit machines with a T-slotted compound rest. The toolpost may also be installed directly to a drilled-and-tapped (8 or 10mm) compound rest with either of the included bolts: an 8mm bolt (with included through-body bushing) or 10mm bolt. The tool post body is 1 1/4" high with a base 1 1/2" wide.

The complete set includes one tool post, one turning tool holder, one turning and boring tool holder, one boring bar holder, one cutoff tool holder, and one multi-tool holder.

Some machining is needed to adapt this post to the Prazi SD-400 and similar 7" swing machines.

To order the correct tool post for your machine, measure the CENTER HEIGHT of your lathe: this is the distance from the top of the compound to the center of the chuck. Match your lathe's center height to a toolpost with a compatible center height range. In situations where your lathe will accommodate more than one size tool post, secondary variables (such as swing, tool size capacity, rigidity, etc.) should then be considered to select the post that you want for your machine.
Quantity Price Model Description Center Height Holds Tool Size
Out of stock
$34.00 PH2-250-079
#2 Turning and Boring Tool Holder 9/32"- 23/32" 1/8 - 3/8" toolbits or round bar
Out of stock
$39.00 PH2-250-081
#4 Boring Bar Holder 9/32"- 23/32" 3/8" round bar
Out of stock
$34.00 PH2-250-083
#6 Multi Tool Holder 9/32"- 23/32" 1/8 - 3/8"
Out of stock
$40.00 PH2-250-085
#7 Cut-Off Tool Holder 9/32"- 23/32" P1 or P1N cutoff blades

A2Z Tool Post Mount Kits

The A2Z Tool Post can be used with different mounting kits for compatability with a wide selection of mini-lathes:

These models are the mount kit only. You must already have an A2Z Tool Post to use them.
Limited Quantity.

These mount kits allow you to use your post on:
Common 7x10, 7x12, 7x14 minis.
Sherline minis.
Taig.
Atlas and Craftsman.
Unimats.
8 x 10 and 8 x 14 lathes.
9 x 20 lathes
Prazi and Emco lathes.

Quantity Price Model Description Use on: